[Discontinued] SainSmart Mega2560 R3 + 2.8″ LCD Screen Display + TFT LCD Shield for Arduino Online now

Description

[Discontinued] SainSmart Mega2560 R3 + 2.8″ LCD Screen Display + TFT LCD Shield for Arduino

Description:
This is SainSmart mega2560 R3 + 2.8 inch TFT LCD module with the TFT LCD shield kit For arduino enthusiasts.It includes one pcs of SainSmart mega2560 R3 , 2.8 inch TFT LCD display and a TFT LCD shield for arduino mega2560. We will provided you the whole document including the example project of the kit. We will supply you the technical support after your purchase.

SainSmart Mega2560  R3

This is the new SainSmart MEGA2560 R3. In addition to all the features of the previous board, the MEGA now uses an ATMega16U2 instead of the ATMega8U2 chip. This allows for faster transfer rates and more memory. No drivers needed for Linux or Mac (inf file for Windows is needed and included in the Arduino IDE), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc.

The SainSmart MEGA2560 R3 also adds SDA and SCL pins next to the AREF. In addition, there are two new pins placed near the RESET pin. One is the IOREF that allow the shields to adapt to the voltage provided from the board. The other is a not connected and is reserved for future purposes. The MEGA2560 R3 works with all existing shields but can adapt to new shields which use these additional pins.

SainSmart 2.8 inch TFT LCD 240X320 Arduino DUE/Mega2560(R3)

SainSmart 2.8″ TFT LCD Display is a LCD touch screen module. It has 40pins interface and SD card and Flash reader design. It is a powerful and mutilfunctional module for your project.The Screen include a controller ILI9325, it’s a support 8/16bit data interface , easy to drive by many MCU like arduino families,STM32 ,AVR and 8051. It is designed with a touch controller in it . The touch IC is XPT2046 , and touch interface is included in the 40 pins breakout. It is the version of product only with touch screen and touch controller.

Specification:

• 240374PQ
• 262K color
• 240*320
• 2.8 inch
• Wide viewing angle
• ILI9325:240 RGB x 320 TFT Driver
• Integrated Power, Gate and Source Driver With RAM
• XPT2046-WIRE TOUCH,WIRE TOUCH, UP TO 125kHz CONVERSION RATE, SERIAL INTERFACE
• Voltage type: 5v or 3v voltage input voltage,input is selectable. Because TFT can only work under 3.3 V voltage, so when the input voltage VIN is 5V, need through the 3.3 V voltage regulator IC step down to 3.3V , when the input voltage of 3.3 V, you need to use the zero resistance make J2 short , is equivalent to not through the voltage regulator IC for module and power supply directly.(Click here)
• Note: the factory TFT module, are the 5 v power supply. By default.
• Carrying on board SD holder, its work to SPI mode.

SainSmart TFT LCD Extend Shield for arduino Mega2560(R3)

This is SainSmart TFT LCD Extend shield for arduino mega2560(R3) .Using this shield can help you out of the bothers to use other cables. You just need to plug the module to arduino mega2560(R3)  through this shield.
Now, the TFT LCD Shield is 100% compatible with arduino mega2560(R3)  and fit for tow kind of TFT LCD module

1. 40pin version LCD which is commonly used in previous version of TFT shield for Arduino mega2560(R3) ( like 2.8/3.2/3.5/4.5/5 inch LCD Display)
2. 32pin version LCD which is commonly used in STM32 development board. (unsoldered)

Package List:

• 1X SainSmart Mega2560 R3
• 1X SainSmart 2.8 inch LCD Display with touchscreen for arduino due mega2560 R3
• 1X SainSmart TFT LCD Extend Shield for arduino Mega2560(R3)
• 1X USB Cable

Note:

• 1. We have confirmed that the LCD is 100% compatible with raspberry pi but we do not have the programmed project yet.
• 2. The shiled is just for arduno Mega2560(R3).If you need the LCD Extend shield for arduino due,you need a similar shield which is also provided from our store.
• 3. Please contact us for the document of the introduction